It is currently Thu Mar 28, 2024 4:17 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 27 posts ]  Go to page Previous  1, 2
Author Message
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Thu Jan 10, 2019 12:18 am 

Joined: Tue Jul 10, 2012 3:51 pm
Posts: 12
Very interesting reading this thread. The ideas here are amazing.

I like the idea of the 600V to 120/240 VAC converter and an automatic battery charger. Safety from overcharging, producing dangerous gas, etc. is important IMO, when you have visitors on the cars. You can even buy an automatic battery charger circuit board 120/240VAC to DC (adjustable) on eBay for a few bucks. Not overly recommending it, but it is possible.

[EDIT] Here is a link for an adjustable 12-36VDC battery lo/hi voltage cutoff circuit:
https://www.ebay.com/itm/XH-M609-DC-12V ... 3741330175

At $4.99 It should be within anyone's budget :).


One important consideration for the Edison batteries - they have a negative temperature coefficient. That is as they charge up their internal resistance decreases. Thus a simple constant voltage charger circuit will "run away" and overload/overcharge them. On the old Waukesha Enginators, they had a separate panel specifically for when Edison batteries were used.

----
I have 4 8V lead acid golf cart batteries that are charged by a Waukesha Enginator (running) or a transformer/rectifier (station power). The car is the old Milwaukee Road Dynamometer car at the Illinois Railway Museum.


Last edited by warren032 on Fri Jan 11, 2019 12:37 pm, edited 1 time in total.

Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Thu Jan 10, 2019 10:55 am 

Joined: Thu Oct 08, 2015 11:54 am
Posts: 1773
Location: New Franklin, OH
This is waaaaay out of my league but I'll throw something similar out there that may be workable or get you thinking....

Start with a 600 to 36 volt converter something like: https://absopulse.com/750vdc-high-input-voltage-railway-dc-dc-converters-transit-mining-vehicles/. Much smaller package. This one may/may not have the needed current available, don't know your requirements. No clue on the cost, though. Could be way out of line with your budget.

Automatic charging circuits are relatively simple affairs once you get past the initial power supply portion. If you have an electronics guru or technical school that'll take that portion on, you might be cooking with gas.

Just a thought...

_________________
Eric Schlentner
Turner of Wrenches, Drawer of Things


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Fri Jan 11, 2019 10:49 pm 

Joined: Fri Mar 14, 2014 11:44 pm
Posts: 198
OK, my two cents, again.

If you are a *museum* then part of the mission is to preserve, to the extent possible, the original
historic fabric. To me, that also includes preserving the obsolete and inefficient technology of the
day.

Solutions that involve solid-state converters and other modern electrical components might be the
best answer for a transit agency, tourist railway, or "heritage" trolley operation where the primary
mission is not historic authenticity.

If the original charging system for these cars was M-G, the best practice from a museum standpoint
is to either rewind the M-G, or as one poster suggested, get an M-G from a PCC car (there are many
of these out there). Then you'll have something which sounds and operates almost like the original.


Regarding the resistive charging scheme: if that's not something the cars ever had, I don't advocate
for it. But as for the safety aspect if the battery goes open, there is a simple, inexpensive and
admittedly anachronistic prophylactic circuit: place a power-rated zener diode in parallel with the
battery having a breakdown voltage of say 50V. If you can't easily find zener diodes that can handle
the power, then use a "crowbar" circuit with an SCR and a zener diode to bias the gate. In the
event of an over-voltage because of an open battery, the crowbar shorts B+ to ground and blows the
battery fuse and charger fuse.


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Mon Jan 14, 2019 7:17 am 

Joined: Thu Sep 29, 2016 4:55 pm
Posts: 28
Hard to restore the origninal South Shore MGs when in East Troy case, im sure a couple of the MGs have disappeared over the last 3 decades.

I disagree about authenticity. you gotta do what you need to do to keep the cars running. If you run the car once a year, then i suppose being original is ok. but if you run it all the time, id go for the best maintence solution. and a solid state inverte/converter is probaly the best bet for East troy.

The riding public is not going to care if the car has an MG or a solid state converter. all they care about is does the car run, and can i ride it.


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Mon Jan 14, 2019 2:38 pm 

Joined: Sun Jul 20, 2008 12:21 am
Posts: 58
Tony, you've got that right! I personally believe
that the equipment should be preserved as best
as possible. That means adhering as much as possible
to the original parts and methods.

You are correct also, in that 99.99999% of the riding public
does not know nor care anything about the details of how it
runs, and why it runs, and what it represents historically.

Especially with the CSS&SB cars, there is always a balance
of these factors to be considered.

Given the fact that these cars are rather complex, keeping
(6) of them on the active roster is a significant challenge.

This situation also provides the opportunity to test
a few different concepts for charging the 32 volt
batteries.


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Tue Jan 15, 2019 7:44 pm 

Joined: Thu Nov 22, 2007 5:46 am
Posts: 2603
Location: S.F. Bay Area
A South Shore M-G set is a fairly beefish piece of metal, and oriented parallel to the carbody near the outside. It would do a fine job of concealing a digital converter installed behind it or above it.


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Tue Jan 22, 2019 3:49 pm 

Joined: Sun Jul 20, 2008 12:21 am
Posts: 58
bump


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Thu Feb 14, 2019 2:46 pm 

Joined: Sun Jul 20, 2008 12:21 am
Posts: 58
bump


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Fri Feb 15, 2019 11:55 am 

Joined: Mon Nov 26, 2007 2:54 am
Posts: 1019
Location: Califoothills / Midwest Prairies / PNW
Since it does not seem to be mentioned in this thread, you might approach a motor shop and ask what it would cost to rewind a motor for 600v operation rather than 1200? I think the result would be less windings on the same motor. I had heard of someone doing this on a much smaller motor in different voltages with good results. I have not heard of volunteers rewinding motors, but perhaps it is possible to do that and save on cost that way.


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Fri Feb 15, 2019 2:12 pm 
User avatar

Joined: Fri Oct 24, 2008 9:05 pm
Posts: 1053
Location: MA
If you do ask about convershion there is a motor shop the Shore Line Trolley museume deals with a lot with good results. Unfortunately I can't remember the name of the shop right now.


Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Wed Apr 03, 2019 10:21 am 

Joined: Sun Jul 20, 2008 12:21 am
Posts: 58
An update on this:

Thanks to all of the very helpful suggestions posted here,
we have made contact with the design engineer at Absopulse Co.
and he has already quoted some prices.

With some more time and effort with this company, these solid state
units should serve our needs quite well on the CSS&SB cars.

Thanks again for all the great suggestions!

Updated Update from 11/14/19:

Insufficient funds are available at this time for purchasing
an Absolulse product. Experimentation is ongoing with the
home-made zener diode based charging regulator. This past
summer of 2019, the experimental unit was temporarily
installed on one of the CSS&SB cars for live testing.

So far, these tests have shown the prototype unit
proof of concept works rather well. Approximate
set points are: Start charging when battery terminal
voltage falls below 36 volts. Charge at 26 amps until
battery terminal voltage reaches 40 volts. This is
a simple regulator which just turns on, or turns off
the charging. The car being tested loads the system
to about 19 amps max load. With 26 amps charging
current that leaves about 7 amps charging when under
full load. This setup was tested extensively this
past summer. Track tested it 2 round trips so far.
Batteries remain cool to the touch throughout these tests.
The next testing phase shall be temperature oriented.
Must determine how the accuracy of it holds up
in low temperatures of late fall and winter, as compared
to summertime. So far it seems to be working ok.

One additional note of explanation: This is no longer
a 32 volt system. It is now nominally a 36 volt system
because the original Edison cells got swapped out
long ago with 2 strings of 3 each 12 volt lead-acid
batteries. These are rated at 150 amp-hour capacity.
The resulting string has 300 amp-hour capacity.

Chuck


Last edited by Chuck Richards on Thu Nov 14, 2019 1:56 pm, edited 1 time in total.

Offline
 Profile  
 
 Post subject: Re: 32 volt battery charging circuit
PostPosted: Thu Nov 14, 2019 1:38 pm 

Joined: Sun Jul 20, 2008 12:21 am
Posts: 58
bump. See updated update above.


Offline
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 27 posts ]  Go to page Previous  1, 2

All times are UTC - 5 hours [ DST ]


 Who is online

Users browsing this forum: Google [Bot] and 67 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: