It is currently Tue Mar 19, 2024 3:09 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Drive Wheel on 6816, should it be hanging over the rail ?
PostPosted: Wed Jul 11, 2018 5:36 pm 

Joined: Fri Mar 18, 2005 1:27 pm
Posts: 552
Location: Milford,Mass
Attachment:
File comment: Photo by Pat Fahey taken from slide
Steamtown Fireless cooker 1980 (2) Resize.jpg
Steamtown Fireless cooker 1980 (2) Resize.jpg [ 65.94 KiB | Viewed 5572 times ]
Attachment:
File comment: Photo by Pat Fahey taken from slide
Steamtown Fireless cooker 1980 resize.jpg
Steamtown Fireless cooker 1980 resize.jpg [ 47.62 KiB | Viewed 5572 times ]
Hi All

I have a question in the shot of the fireless cooker at Steamtown in Vermont that I took in Oct 1980. The rear drive wheel should it be hanging over the rail that much? Just wondering why is it because the tires are overworn?


Offline
 Profile  
 
 Post subject: Re: Drive Wheel on 6816, should it be hanging over the rail
PostPosted: Wed Jul 11, 2018 8:15 pm 

Joined: Sun Aug 22, 2004 1:51 pm
Posts: 11473
Location: Somewhere east of Prescott, AZ along the old Santa Fe "Prescott & Eastern"
Wider tires were common on many switchers that had to contend with tight curves and/or rough track. It gave a wider "margin of error" and theoretically reduced derailments, although the wider tires could themselves induce problems on places like street trackage.


Offline
 Profile  
 
 Post subject: Re: Drive Wheel on 6816, should it be hanging over the rail
PostPosted: Wed Jul 11, 2018 8:41 pm 

Joined: Fri Aug 20, 2010 8:25 pm
Posts: 485
It's a little hard to tell from those photo's, but it appears that the center driver of that switcher is a "Blind Driver". These were relatively wide drivers without a flange (no flange at all just a flat tire surface).

These blind drivers along with wide tires on the other drivers were common with long wheel base loco's. They allow the loco to go through tighter curves without binding caused by the flanges.

I had not seen one applied to a switcher before, but it makes sense. The flanges on the front & rear driver tires "steer" the loco and the blind center driver just "pushes" the loco.

If this loco was built for a power plant or factory that had "tight" curves a blind center driver and wide tires could have been specified by the customer as an "option". Like power steering on a 1970's Chevelle.....

Cheers, Kevin


Offline
 Profile  
 
 Post subject: Re: Drive Wheel on 6816, should it be hanging over the rail
PostPosted: Thu Jul 12, 2018 2:00 am 

Joined: Wed Sep 25, 2013 12:36 am
Posts: 594
Location: Anchorage, Alaska
Probably not applicable to this locomotive, but another reason for using a wide tire applied to a number of Moguls built in 1906 for construction of the Panama Canal and obtained by the Alaska Railroad in 1915. They were converted from 5 foot gauge to standard gauge in Panama. The drivers had wide tires to make the gauge conversion. I understand that they had some problems derailing at grade crossings during the winter when the drivers were lifted off the rail by ice on the outside of the rails that wasn't cleared by standard width wheels.


Offline
 Profile  
 
 Post subject: Re: Drive Wheel on 6816, should it be hanging over the rail
PostPosted: Thu Jul 12, 2018 5:34 am 

Joined: Thu Apr 14, 2005 9:34 pm
Posts: 2752
Location: Copenhagen, Denmark
If the rail is light, it will make the tires look wider too.

_________________
Steven Harrod
Lektor
Danmarks Tekniske Universitet


Offline
 Profile  
 
 Post subject: Re: Drive Wheel on 6816, should it be hanging over the rail
PostPosted: Thu Jul 12, 2018 9:08 am 

Joined: Tue Sep 14, 2004 7:52 am
Posts: 2558
Location: Strasburg, PA
Alexander D. Mitchell IV wrote:
Wider tires were common on many switchers that had to contend with tight curves and/or rough track. It gave a wider "margin of error" and theoretically reduced derailments.

The standard width for tires is 5-1/2". By coincedence, we currently have a wheel set on the shop from a logging locomotive whose tires measure 6-1/4" wide.


Offline
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


 Who is online

Users browsing this forum: Google [Bot], Majestic-12 [Bot] and 46 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: